DVR OPERATING INSTRUCTIONS
BASIC CCTV OPERATION GUIDE
1. HDD INSTALLATION
For the first use, please install the hard disk. Every series product supports
SATA interface HDD. (Remark: the device can run normally without HDD,
but cannot do record and playback.)
2. DVR/NVR KIT ‘S CONNECTION METHOD
3.SYSTEM LOGIN
When the DVR/NVR boots up, the user must login and the system provides
the corresponding functions with the user purview. There are three user
settings. The names are admin, guest and default and these names have no
password. The default user name is “admin”. To modify user name and
password ,Please click<Main menu>-<Advanced>-<Account >.
Admin is the super user purview; guest and default’s permissions are preview
and video playback. User admin and guest’s password can be revised, while
their permissions can’t be revised; user default is the default login user whose
permission can be revised but not its password.
Password protection: If the password is continuous wrong three times, the
alarm will start. If the password is continuous wrong five times, the account
will be locked. (through reboot or after half an hour, the account will be
unlocked automatically).
For your system security, please modify your password after first login.
4. DVR NETWORK CONFIGURATION
Please follow up Configuration Wizard step to setup DVR/NVR network. Or
click <Main menu>- <System>--<Network> to setup.
Please make sure the device IP Address , Gateway and router are in the
same network segment, Primary DNS is the same with Gateway.
Secondary DNS is 8.8.8.8
5.CHANNEL MANAGE
This chapter includes “Manually add camera”, “Modify camera IP address”.
“Select recording resolution and playback channel”.
5.1 DVR Channel Manage
5.1.1 Select Recording resolution. Playback channel.
<1>Click<Main Menu>-<System>-<Digital >.Then popup the following page.
<2>Click <Channel Type>.You can select recording channel, playback
channel and recording resolution. See picture 6:
In the above picture, recording channel is 4, playback channel is 2, recording
resolution is 1080P.
5.2 NVR Channel Manage
5.2.1 Select Recording resolution. Playback channel.
<1>Click<Main Menu>-<System>-<Digital >-<Digital channel> ( setup
method is the same with DVR. See 5.1.1 chapter)
5.2.2 Add IP camera
There are two ways to add IP camera. 1.Automatically add camera 2.Manually add camera.
Automatically add camera
Please follow the Configuration Wizard to select “Auto-connected mode”
when you first time connect cameras.
Manually add camera(You can modify camera IP address in this step)
<1>Click<Main Menu>-<System>-<Digital>. Then popup the following page
<2> Click <Digital channels>-<Add> -<Search>, will show all the device that
searched out, Select the device listed. Double click it. See picture 8.
Remark: when the current resolution is over the max resolution that the channel
supported, then a red “X” will be shown on the preview image.
6. CCTV DVR RECORD CONFIGURATION
Set the recording parameters in the surveillance channel. The system is set 24
hours recording in the first startup. You can enter <Main Menu>-<Record>-
<Recording Config> to set. See picture 10:
【Channel】Select record channel. You can select “All”. If you want to
setup separately, you also can set one by one.
【Length】Set the time length of each video file. 60minutes is the default
value.
【Record Mode】
Schedule: Setup recording in a period time. Select date in<Week>,Select
time in<Period>
Manual: Recording 24 hours a day
Stop: Stop recording
【Pre-Record】Record 1-30 seconds before the action. (time length is
decided by the code stream)
7. XMEYE DVR PLAYBACK
<1>Right click, select <Playback>
Note: The hard disk that saves the video files must be set as read-write or
read-only state.
<2>Select the playback channel, the date, click refresh button which
is on the bottom right side. Then popup a page. Select a video file. Double
click it. See picture11:
1. Playback control 2. Operation hint 3. File searching
4. Listed files 5. File information
【Playback control】See detail in below chart
【Listed files】Look up the listed files that accord with the searching criteria.
【File information】Look up the found file information.
Note: play under frame by frame, the playback status should be paused
firstly
Special function
Accurate playback: Click refresh . Then input time (h/m/s) in the
time column on the top right. and then click play button. The system can
operate accurate playback according to the searching time.
Local zoom: When the system is in single-window full-screen playback mode,
you can drag your mouse in the screen to select a section and then left click
mouse to realize local zoom. You can right click mouse to exit.
Note: When the current resolution of the channel is over DVR/NVR Max
resolution, to playback this channel, will show a Red “X”.
8. MULTI-CHANNEL PLAYBACK
<1> Select playback channels. Click<Main Menu>-<System>-<Digital>-
<Channel Type>.Select the playback channels you need.(Note: playback
channel is on the bottom left side.)
<2> Click-<Playback>
<3>In the search page, select the file type, select multi-channels , select date.
Click to refresh the page. See picture 14:
Note: When current resolution of the channel is over DVR/NVR Max
resolution, to playback this channel, will show a Red “X”
9. XMEYE DVR ALARM SETUP
9.1 Setup Motion Detection IN XMEYE DVR
When system detects the motion signal that reaches the set sensitivity, the
motion detect alarm is on and the linkage function is turned on.
Click<Main Menu>-<Alarm>-<Motion Detect>, See picture 16:
Select the motion detection channel, click <Enable>, adjust the sensitivity
level, Click <Set> next to <Region>, holds down the left mouse button from
left to right to select. See picture 17 (note: the default area is motion detection
area.). Select<Record channel> for motion detection recording. According to
your requirements to Select <Show message> <Send email> <Buzzer>
<Write Log> <FTP upload> <Mobile reported> (Please use the same
method to setup other channels motion detection.)
Other Functions Introduction
【MD Interval 】Only one alarm signal is turned on even there are several
motion detect signals in the set interval.
【Alarm out】Start the external equipment of the corresponding linkage
alarm when the motion detection alarm is turned on.
【Out delay】Delay a few moments and stop when the alarm state is turned
off. The range is 10~300 seconds.
【Tour】Means that selective channels single window alternate patrol
preview. The interval is set in the [Main Menu]>[System] > [Tour].
【PTZ Activation】Set the PTZ activation when the alarm is turned on.
*Hybrid mode, PTZ link to related PTZ information of analog channel, while
digital channel model, the PTZ is linked to the related PTZ information on the
remote device connected. Note to link PTZ, need go [Shortcut menu]->[PTZ
control] to set preset point, cruise between points & interval time, etc.
【FTP upload】to tick it, the video & picture of related record channel &
snapshot channel will be uploaded to assigned position.
Note: FTP upload need be set at [Net service]
9.2 Setup Motion Detection Recording
<1> Setup DVR/NVR motion detection. (follow “9.1 Setup Motion Detection”
chapter).
<2> Setup IP camera motion detection on CMS. There are 3 steps. (Only IP
camera need operate this step, analog camera doesn’t need.)
(1)Add IP camera to CMS.(follow “Part 3 WAN connection 1.1 chapter”.)
(2)Right click the channel, Click the second icon on the bottom,
Click<Video Motion>, See picture18.19:
(3) Select the channel, click <Enable>, adjust the sensitivity level, Click
<Set> Next to <Region>, hold down the left mouse button from left to
right to select the area. It can be repeated to select. According to your
requirements to chose <Send email> <Buzzer> <FTP> <Write log>.
<3>Then add DVR/NVR to CMS software.(Please follow “Part 3 WAN
Connection 1.1 chapter” to operate.) Right click on screen. Click<Device
Config>---<Record>. See picture 20:
<4>Select Channel for motion detection recording. Cancel ticking
<Regular> .Click OK. See picture 21:
Note: If you need to setup motion detection recording on other channels.
Please operate the same way.
9.3 Setup Video Blind
When the video image is influenced by the environment such as bad
brightness or reaching the set sensitivity parameter, the camera mask function
is turned on and the linkage function is turned on.
Operation is the same with motion detection.(See 9.1 Motion Detection)
9.4 Setup Video loss
When the equipment can not obtain the channel video signal, the video loss
alarm is turned on and the linkage function is turned on.
Operation is the same with motion detection.(See 9.1 Motion Detection)
10. XMEYE DVR PTZ DEVICE /RS485 DEVICE
Click<Main Menu>-<System>-<PTZ Config>
【Channel】Select the dome camera in put channel.
【Protocol】Select the corresponding dome protocol. (PELCOD as
an example)
【Address】Set as the corresponding dome address. Default: 1.
(Note: The address must be consistent with the dome address.)
【Baud rate】Select the corresponding dome baud rate length. You
can control the PTZ and vidicion. Default: 115200.
【Databits】lnclude5-8options.Default:8.
【Stop bits】Include 2 options. Default: 1.
【Parity】Include odd check, even check, sign check, blank check.
Default: void.
11. PREVIEW
Login normally and choose the multi-menu preview status.
The system date, time and channel name are shown in each viewing
window. The surveillance video and the alarm status are shown in
each
window.
12.BACKUP
You can backup the video files to external storage through setup.
Note: The storage must be installed before the file backup. If the
backup is terminated, the already backup can playback
individually.
<1>Plug a USB flash disk into DVR/NVR.
<2>Click <Main Menu>-<Record>-<Backup>.Tick the device,
Click<Backup>.See picture 26
<3>Then popup a page. Select the Channel, Input Start time and End
time. Click <Add>.You will find video files on the following list.
Tick the file you want to backup. Select a <Backup format>.Click
start. It begins to backup. That’s ok. See picture 27.
13. DVR TIME AND LANGUAGE SETUP
<2> Click<ADD AREA>, Input a zone name. Click ok. Select the
name of the Zone List. Click<ADD DEVICE>.Then popup a page.
See picture 29. Click<IP Search>,There will show device IP address .
Select the searched IP address. Then click<Add Device>.Click
OK.(To add other devices, Please operate the same way.)
Now you can view the picture on your computer. See picture 30:
WAN CONNECTION
1. Multi-device management platform software-CMS
Multi-device management platform software CMS is a professional
software to remote monitoring of multiple devices, safe, convenient,
stable and unified. No need to download plug-ins, recommends
customers to use.
1.1 ADD DVR/NVR/ IP Camera to CMS
<1>Download CMS software from the CD, follow the tip to install it.
<2>After installing CMS on computer. Double click CMS icon on
desktop. Click login.
Click<System>-<Device manager>,Then popup a page. Click<ADD
AREA>, Input zone name. Click ok. See picture 31:
<3>Select the name in the Zone list. Click<ADD DEVICE>.Then
popup a page. See picture 32.Click <Cloud>, Input device Serial
number. Saved.
Note: Add DVR/NVR to CMS, Please input DVR/NVR serial
number.
Add IP camera to CMS, Please input IP camera serial number.
(Searching DVR/NVR/IP Camera serial number, Please follow
“Part 3 WAN Connection 1.2 and 1.3 chapter ”)
Then you can view the picture on your computer remotely.
Note
Please make sure camera ,nvr, router are in the same segment.
Click<Main menu>-<Info>-<Version> to find the NAT status to
check.
If the NAT status is Connected. That is ok. If it is Probing DNS, that
means
the camera ,nvr ,router are not in the same segment.
(1) To modify NVR segment. Please click <Main menu>-
<System>--<Network> to modify.
(2) To modify IP camera segment. Please follow “Part 1 Basic
Operation 5.2.2 chapter ” operation.
1.2 Searching DVR/NVR serial number
Please operate on DVR/NVR, Right click<Main Menu>-<Info>-
<Version> to find DVR/NVR serial number.
1.3 Searching IP camera serial number
<1> In LAN connection status. Click<IP Search> to search device.
Select the searched IP address, Click<Add device>.Click<OK>. Then
you will see the device on the top left side.
<2>Select IP cameras added on the device list, double click it. The
picture shows on the screen. Right click on the picture.
Select<Device config>,Then popup a page. Select the fifth icon on
the bottom. Click <Version>, See picture 34
Note: How to distinguish video recorder and IP camera in the
searched IP addresses ?
Click on one IP address added, if there are many cameras shown in
the list, that is video recorder. If there is only one device shown. That
is IP camera. You can right click it to rename.
0 Comments